![]() ![]() ![]() Type, which was first made available in JMRI version 2.13.7. WhenĬonfiguring to communicate with the device via USB, be sure that Flow Control isĬonnection via an Ethernet connection is available through the LI-USB Ethernet connection So the USB connection is supported by any JMRI version with support for the LI-USB. The protocol used to connect to the device via USB is identical to the prior LI-USB device, (where XXX is replaced with a 3 digit number) For MacOS users, the device name will be /dev/tty.usbmodemXXX For Linux users, the device will appear as a /dev/ttyACMx device (where x is The USB connection on the device is provided byĪ Microchip chipset and registers itself as a USB CDC-ACM (Abstract Control Model) device.įor Windows users, connection via the USB port will be identical to the previous version of Which includes a built-in Ethernet adapter. The Lenz LI-USB-Ethernet (Lenz part number 23151) is a revised version of the LI-USB.On Windows, starting with version 2.7.2, JMRI supports interfacing with the LI-USB Provides a tool that will allow users of other operating systems to configure their LI-USBĪs well. Thereĭevice is configured via a software tool provided by Lenz which runs on Windows only. Update in your command station, you should also update your LI-USB to version 3.6. Note: If you are using the XpressNet version 3.6 Internally, the device contains a USB to RS232 serial adapter, and an XpressNet interfaceĬircuit similar to that of the LI101F. The Lenz LI-USB (Lenz part number 23150 ) is Lenz's first USB based computer interface.We have included a configuration tool with JMRI that willĪllow users of other operating systems to configure their LI101F as well. The device is configured via a software tool provided by Significantly different than the LI100 and LI100F in physical appearance, and in the methodīy which the device is configured. The Lenz LI101F is Lenz's last serial port based computer interface.It supports serial port speeds ofĩ,600 and 19,200 baud. The Lenz LI100F is an improved version of the LI100.The Lenz LI100 is Lenz's original computer interface.ZTC Controls ZTC521 (with XpressNet (aka X-Bus V3.0) software)Ĭurrently the following XpressNet computer interfaces are supported by JMRI:.Unknown The following systems are untested, but should be at least partially Paco Canada's RS2PC (adds RS-Bus based Feedback without XpressNet).Paco Canada's GenLI-S88 (adds Feedback to existing XpressNet System).ZTC Controls ZTC511 (with Command Station Software version 4.0).Roco MultiMouse (Roco Part number 10810).Roco LocoMaus 2 (Roco Part number 10760).Lenz LZV200 based systems (software version 3.x).Lenz LZV100 based systems (software version 3.x).Lenz LZ100 based systems (software version 3.x).Specific limitations are also expressed in the Limitations section The following table tries to show which systems support these three feature groups. Getting Feedback from the layout (the state of turnouts, ops-mode.Programming decoders on a programming track or in ops mode.Operating Locomotives and Turnouts on the layout.In general, the features that JMRI cares about can be grouped into three areas: You can access via JMRI - if the hardware doesn't support it, it isn't there to be used by Unfortunately, this restricts the features "supports all features" to "bare bones minimal". The XpressNet protocol allows the DCC manufacturers that use it to select whatįunctionality they wish to provide in their command stations. ) specifies the electrical communications standards and command set for devices The XpressNet specification ( available from ![]() Roco (some models), Viessmann and ZTC Controls. XpressNet is a Command Bus developed by Lenz and used by: Atlas, Hornby, Lenz, OpenDCC Layout Automation Use JMRI to automate parts of your layout and operations: ![]() Tools JMRI tools for working with your layout: ZTC Controls Applications By the community of :.XPressNet Log Supported Hardware Devices, command stations, networks, and protocols:. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |